- The ultimate solution for bi-amping loudspeakers: 300 Watt vacuum tube amplifier and 600 Watt solid state amplifier on one chassis
- Vacuum tube section powers mid and upper drivers
- Solid state section drives power hungry woofers
- DualView™ Power Output Meter
MC901
Dual Mono Amplifier
McIntosh has been perfecting vacuum tube amplifiers since the 1940s and solid state amplifiers since the 1960s. Our amplifiers have been used at many historic events including presidential inaugurations and Woodstock, as well as in landmark sound systems like the Grateful Dead's Wall of Sound and Despacio. From that heritage comes a truly one-of-a-kind home audio amplifier only we could dream of, design and build as the ultimate solution for bi-amping loudspeakers: the McIntosh MC901 Dual Mono Amplifier.

The MC901 is a monoblock amplifier that drives a single speaker. But it is unlike any other monoblock amplifier. What makes the MC901 so unique is that it's two amplifiers combined into one. Adding to the uniqueness is that each amplifier is of differing design philosophies: the MC901 consists of a 300 Watt vacuum tube amplifier attached to a 600 Watt solid state amplifier on one unified chassis.

The 300 Watt vacuum tube portion powers the speaker's mid and upper drivers via eight KT88 output tubes, plus four 12AT7 and two 12AX7A signal tubes; the solid state section delivers 600 Watts of dedicated power to the power hungry woofers. The 300 Watt vacuum tube amp in the MC901 uses our patented Unity Coupled Circuit output transformer – the same technology McIntosh was founded on in 1949 – to deliver its full 300 Watts into almost any speaker regardless if it has 2, 4 or 8 Ohm impedance. Similarly, the 600 Watt solid state amp delivers its full 600 Watts into a 2, 4 or 8 Ohm impedance speaker via our Autoformer™ technology.

Vacuum tubes do not perform at their best when they are amplifying lower frequencies that are not being used by the loudspeaker. With the MC901, the vacuum tube amp will not be burdened with low end reproduction as the solid state section will drive these frequencies. The two amplifier sections of the MC901 are designed to work together in a synergistic relationship and are specifically engineered to assure that each section only amplifies its intended frequencies. Each amplifier section has its own discrete power supply so neither siphons power or performance away from the other. All of this results in easy bi-amping with unparalleled performance and sound reproduction from your speakers.
WATCH: Discover why Steve Guttenberg The Audiophiliac Man "reached new heights of aural ecstasy" when listening to the MC901 Dual Mono Amplifier at the World of McIntosh Townhouse.

Prior to the MC901, bi-amping a speaker required two separate amplifiers. It also required an external crossover, along with a lot of trial and error, to properly configure the two detached amplifiers so they worked together as best as possible. The MC901 solves this issue thanks to its internal, adjustable crossover with the controls easily accessible on the top of the unit. These adjustable crossover filters allow you to optimize the performance of both amplifier sections to your listening preferences. Relative gain levels for each amplifier section can be adjusted from -6dB to + 3dB. A direct feed can also be connected to each amplifier section, thus bypassing the filters.

Like virtually all McIntosh amplifiers, the MC901 features an iconic "McIntosh Blue" Watt meter, which has come to be recognized around the world as a symbol of quality home audio. And just like the MC901 itself is a new design, so too is its meter with the introduction of our new DualView™ Power Output Meter. The DualView meter features two of our traditional, fast responding mechanical meters stacked above and below each other in a single meter window; one meter is dedicated to the 300 Watt vacuum tube amp and the other to the 600 Watt solid state amp. Each meter operates independently of the other and displays the real time power reading of each amplifier section.
While an entirely new design, the MC901 comes with the technology one would expect from a McIntosh amplifier:
- Power Guard® that monitors and adjusts the input signal in the 600 Watt solid state amplifier section in real time, then makes unobtrusive adjustments to prevent harsh sounding distortion and potential speaker damaging clipping.
- Power Guard Screen Grid Sensor™ (SGS). The 300 Watt vacuum tube amplifier section of the MC901 breaks new ground as it's our first amplifier to feature our new Power Guard SGS™ technology. Power Guard SGS helps prevent premature vacuum tube failure by monitoring the screen grid current in the KT88 output vacuum tubes. If the current becomes too high, a circuit in Power Guard SGS is activated which then dynamically attenuates the input signal in real time to keep the vacuum tubes operating at safe levels.
- Sentry Monitor™ observes the output current and shuts the amplifier off if it ever exceeds safe limits.
- Quad Balanced design that cancels virtually all noise and distortion that may have crept into the audio signal.
- Power Control that can send power on/off signals to other connected McIntosh components for easy system power up and shutdown.
- Our patented, gold-plated Solid Cinch™ speaker binding posts that easily and securely attach the speaker cables.
- McIntosh Monogrammed Heatsinks™ that are connected to advanced high current output transistors efficiently cool the solid state amplifier section.
- Our Power Management System that will turn the entire unit off after a set amount of time when no input signal has been detected.

Although the MC901 may look different than any McIntosh product before it, a quick glance reveals signature McIntosh design cues. The top is highlighted by a series of diagrams printed on glass that outline the basic circuitry and specifications of the unit, along with a glass nameplate trimmed with a circular aluminum ring that's finished to match the front panel endcaps. The sides are adorned with vintage McIntosh-styled die cast aluminum name badges. Two classic McIntosh knobs are located on the front of the polished stainless steel chassis, and direct LED backlighting illuminates the DualView meter, McIntosh logo and the lettering on the black glass front panel.
The uncompromising level of fit and finish that is expected of a McIntosh product completes the MC901. It can be combined with a variety of preamplifiers, turntables, CD players, media streamers, speakers and other specialty products to form a complete home audio system. Contact your local dealer to learn more about this one-of-a-kind home audio amplifier.
-
Specifications
Electronic Specifications
-
- Power Output per Channel
- Solid State section: 600 Watts @ 2, 4 or 8 Ohms
Vacuum Tube section: 300 Watts @ 2, 4 or 8 Ohms
-
- Number of Channels
- 1
-
- Total Harmonic Distortion
- Solid State section: 0.005% maximum harmonic distortion at any power level from 250 milliwatts to rated power, 20Hz to 20,000Hz
Vacuum Tube section: 0.5% maximum harmonic distortion at any power level from 250 milliwatts to rated power, 20Hz to 20,000Hz
-
- S/N below rated output
- Solid State section: 122dB
Vacuum Tube section: 112dB
-
- Dynamic Headroom
- Solid State section: 2.5dB
Vacuum Tube section: 1.2dB
-
- Damping Factor
- Solid State section: >40
Vacuum Tube section: >18
-
- Rated Power Band
- Solid State section: 20Hz to 20kHz
Vacuum Tube section: 20Hz to 20kHz
-
- Frequency Response
- Solid State section:
+0, -0.25dB from 20Hz to 20,000Hz
+0, -3dB from 10Hz to 100,000Hz
Vacuum Tube section:
+0, -0.5dB from 20Hz to 20,000Hz
+0, -3dB from 10Hz to 70,000Hz
Control
-
- Remote Power Control
- Yes
-
- Multi-Channel DB25 Cable
- N/A
Connectivity
-
- Speaker Binding Post Type
- Patented Solid Cinch™ Speaker Binding Posts
General Specifications
-
- Circuit Configuration
- Solid State section: Quad Balanced
Vacuum Tube section: Unity Coupled
-
- Circuit Design
- Solid State and Vacuum Tube
-
- Mono Bridge
- No
-
- Mono Parallel
- No
-
- Output Type
- Solid State section: Autoformer™
Vacuum Tube section: Unity Coupled Output Transformer
-
- Meters
- DualView™ Power Output Meter
-
- Meter Light Switch
- Yes
-
- Balanced Input
- 3 (1 Solid State, 1 Vacuum Tube, 1 Composite)
-
- Front Panel
- Glass
-
- Illumination
- Direct LED
-
- Chassis Style
- Polished stainless steel & black painted steel
Weights & Dimensions
-
- Unit Dimensions (W x H x D)
- 17-17/32" (44.5cm) x 13-3/8" (34cm) x 29-17/32" (75cm)
-
- Unit Weight
- 180 lbs (81.6 kg)
-
- Shipping Weight
- 200 lbs (90.7 kg)
-
-
Downloads
Product Literature User Documents - MC901 Dual Mono Amplifier Brochure (2.05 MB)
- MC901 Dual Mono Amplifier Owner's Manual (9.31 MB)
- MC901 Dual Mono Amplifier Dimensions (0.37 MB)
More from Amplifiers
-
MC2KW
1-Channel Solid State Amplifier
- 2,000 Watt Quad Balanced Monoblock
- 3 speaker terminals for tri-wiring
- 2 Power Modules, 1 Output Module
-
MC1.25KW
1-Channel Solid State Amplifier
- 1,200 Watt Quad Balanced Monoblock
- Redesigned from top to bottom
-
MC611
1-Channel Solid State Amplifier
- 600 Watt Quad Balanced Monoblock
- 55% increase in Dynamic Headroom compared to previous model
-
MC3500
1-Channel Vacuum Tube Amplifier Mk II
- 350 Watt Monoblock
- Inspired by the original 1968-71 MC3500 – the Amplifier that Inspired a Generation
- Powered by eight EL509S high-power output vacuum tubes
- Power Guard Screen Grid Sensor™, Sentry Monitor, Solid Cinch speaker binding posts
- Machined aluminum front panel with a bead blast finish and gold anodizing
-
MC830
1-Channel Solid State Amplifier
- 300 Watts into 8 Ohms
- 480 Watts into 4 Ohms
- Power Guard, Sentry Monitor, Monogrammed Heatsinks, Solid Cinch speaker binding posts
-
MC462
2-Channel Solid State Amplifier
- 450 Watts x 2 Channels
- 66% increase in Dynamic Headroom compared to previous model
- Quad Balanced Design with McIntosh Autoformers™
-
MC312
2-Channel Solid State Amplifier
- 300 Watts x 2 Channels
- 27% increase in Dynamic Headroom compared to previous model
- McIntosh Autoformers™
-
MC2152
70th Anniversary 2-Channel Vacuum Tube Amplifier
- 150 Watts x 2 Channels
- Unity Coupled Circuit Output Transformers
- (8) KT88, (4) 12AX7A and (4) 12AT7 vacuum tubes
- Striking new design with carbon fiber side panels
-
MC1502
2-Channel Vacuum Tube Amplifier
- 150 Watts x 2 Channels
- Unity Coupled Circuit Output Transformers
- (8) KT88, (4) 12AX7A and (4) 12AT7 vacuum tubes
-
MC275
2-Channel Vacuum Tube Amplifier
- 75 Watts x 2 channels or 150 Watts x 1 channel
- Unity Coupled Circuit Output Transformers
- (4) KT88, (4) 12AT7 and (3) 12AX7A vacuum tubes
- One of the most iconic amplifiers ever made by any brand
-
MC303
3-Channel Solid State Amplifier
- 300 Watts x 3 Channels
- Designed for home theaters
- Tri-Amp capability
-
MC255
5-Channel Solid State Amplifier
- 250 Watts x 3 Channels; 200 Watts x 5 Channels
- TripleView™ Power Output Meter
- More than 100% increase in Dynamic Headroom
- Dynamic Power Manager®; Power Guard®
- Designed for home theaters
-
MC257
7-Channel Solid State Amplifier
- 250 Watts x 3 Channels; 200 Watts x 7 Channels
- TripleView™ Power Output Meter
- 94% increase in Dynamic Headroom
- Dynamic Power Manager®; Power Guard®
- Designed for home theaters
-
MC8207
7-Channel Solid State Amplifier
- 200 Watts x 7 Channels
- Designed for home theaters
- LED power output indicators
-
MI347
7-Channel Digital Amplifier
- Designed for home theaters
- 3 Front Channels: 250 Watts into 8 Ohms or 300 Watts into 4 Ohms
- 4 Surround Channels: 125 Watts into 8 Ohms or 200 Watts into 4 Ohms
- 3U rack mountable
- Power Guard® and Sentry Monitor™
-
MI254
4-Channel Digital Amplifier
- Perfect for home theater surround sound speakers
- 250 Watts into 8 Ohms
- 300 Watts into 4 Ohms
- 2U rack mountable
- Can also be used in distributed audio
- Bussable inputs
- Signal sensing
- Power Guard® and Sentry Monitor™
-
MI128
8-Channel Digital Amplifier
- Ideal for multi-zone distributed audio
- 120 Watts into 8 Ohms
- 150 Watts into 4 Ohms
- 2U rack mountable
- Channel summing circuits for mono signal distribution
- Volume controls for each channel
- Bussable inputs
- Signal sensing
- Power Guard® and Sentry Monitor™
-
MI1250
12-Channel Digital Amplifier
- Ideal for multi-zone distributed audio
- 50 Watts into 8 Ohms
- 90 Watts into 4 Ohms
- 2U rack mountable
- Channel summing circuits for mono signal distribution
- Volume controls for each channel
- Bussable inputs
- Signal sensing
- Power Guard® and Sentry Monitor™
Recommended Products
ASK AN EXPERT:
MC901
Dual Mono Amplifier
* Required Field
Thank you for contacting McIntosh Laboratory, Inc. We will reply to your message as soon as possible.
Compare Products:
PLEASE SELECT PRODUCTS TO COMPARE
-
MC901
Dual Mono Amplifier
-
MC2KW
1-Channel Solid State Amplifier
-
MC1.25KW
1-Channel Solid State Amplifier
-
MC611
1-Channel Solid State Amplifier
-
MC3500
1-Channel Vacuum Tube Amplifier Mk II
-
MC830
1-Channel Solid State Amplifier
-
MC2301
1-Channel Vacuum Tube Amplifier
-
MC462
2-Channel Solid State Amplifier
-
MC312
2-Channel Solid State Amplifier
-
MC152
2-Channel Solid State Amplifier
-
MC2152
70th Anniversary 2-Channel Vacuum Tube Amplifier
-
MC1502
2-Channel Vacuum Tube Amplifier
-
MC275
2-Channel Vacuum Tube Amplifier
-
MC303
3-Channel Solid State Amplifier
-
MC255
5-Channel Solid State Amplifier
-
MC257
7-Channel Solid State Amplifier
-
MC8207
7-Channel Solid State Amplifier
-
MI347
7-Channel Digital Amplifier
-
MI254
4-Channel Digital Amplifier
-
MI128
8-Channel Digital Amplifier
-
MI1250
12-Channel Digital Amplifier